Honda HR-V: Keyless Access System Symptom Troubleshooting - Immobilizer
Indicator Does Not Go OFF Or Does Not Come ON
1. Keyless access system check 1.
- Turn the vehicle to the OFF (LOCK) mode.
- Turn the vehicle to the ON mode.
- Check the immobilizer indicator.
Does the immobilizer indicator come on?
YES
Go to step 2.
NO
Go to step 5.
2. Keyless access system check 2:
- Check the immobilizer indicator.
Does the indicator come on, then go off?
YES
Go to step 3.
NO
Go to step 7.
3. Keyless access system check 3
- With driver's power window open, turn the vehicle to the OFF (LOCK)
mode.
- Remove all the keyless remotes from inside the vehicle. Place the
keyless remotes more than 7.87 in
(20 cm) away from the vehicle.
- Press the engine start/stop button. The gauge control module should
request the keyless remote to
touch the engine start/stop switch. The LED on the engine start/stop switch
will flash for up to 30
seconds.
- Touch the engine start/stop switch with the keyless remote. The buttons
on the keyless remote should
be facing you. The LED on the engine start/stop switch will turn solid when
detected.
- Turn the vehicle to the ON mode.
- Check the immobilizer indicator.
Does the indicator blink once, then stay off?
YES
Intermittent failure, the system is OK at this time.
NO
Go to step 4.
4. Keyless access system check 4:
- Select BACK-UP CONTROL UNIT from the ONE-PUSH START system select menu
with the HDS,
and enter SYSTEM INFORMATION.
One-Push - BACKUP CONTROL UNIT - System Information
- Do the SYSTEM CHECK with the HDS.
Is N-1 OK indicated?
YES
Replace the gauge control module.
NO
Troubleshoot the keyless access system according to the result of the SYSTEM
CHECK.
5. PGM-FI system check:
- Check the malfunction indicator lamp (MIL).
Does the indicator come on?
YES
Go to step 6.
NO
Replace the gauge control module.
6. PGM-FI DTC check:
- Check for Pending or Confirmed PGM-FI System DTCs with the HDS.
.png)
DTC (PGM-FI)
Are any DTCs indicated?
YES
Go to the indicated DTC troubleshooting - Refer to: Fuel and Emissions
Systems DTC Troubleshooting Index (KA/KC), or CVT System DTC Troubleshooting
Index (KA/KC CVT).
NO
Replace the gauge control module.
7. Keyless access system check.
- Select KEYLESS ACCESS CONTROL UNIT from the ONE-PUSH START system select
menu with
HDS, and enter SMART INFORMATION.
One-Push - KEYLESS ACCESS CONTROL UNIT - Smart Information
- Do the SYSTEM CHECK 1 and 2 with the HDS.
Is N-1 OK indicated?
YES
Replace the gauge control module.
NO
Troubleshoot the keyless access system according to the result of the SYSTEM
CHECK 1 and 2.
READ NEXT:
1. Keyless access system check.
Turn the vehicle to the OFF (LOCK) mode.
Turn the vehicle to the ON mode.
Check the keyless access indicator.
Does the keyless access indicator come on for 2 seco
1. Keyless access system check.
Turn the vehicle to the ON mode.
Does the system change to ON mode?
YES
Go to step 2.
NO
Go to the keyless access system symptom troubleshooting "Cannot select ON
m
1. Door lock actuator operation check 1.
Remove all the keyless remotes from inside the vehicle, and close all
doors and the tailgate.
Push each LOCK and UNLOCK buttons of the keyless remote, at
SEE MORE:
CVT SYSTEM DTC TROUBLESHOOTING INDEX (KA/KC CVT)
NOTE: Before you troubleshoot, record all freeze data and any on-board
snapshot with the HDS, and review the General Troubleshooting Information -
Refer to: How to Troubleshoot the Fuel
and Emissions Systems, or How to Troubleshoot the CVT System (C
HOW TO TROUBLESHOOT THE BODY ELECTRICAL
Tips and Precautions
Special Tools Required
Back Probe Adapter, 17 mm 07TAZ-001020A
Before Troubleshooting
1. Check applicable fuses in the appropriate fuse/relay box.
2. Check the 12 volt battery for damage, state of charge, and clean and tight
connections.