Honda HR-V: SRS Symptom Troubleshooting - Front Seat Belt Reminder Indicator Does Not Come ON, Turn OFF, Or Flash (KA/KC)
NOTE:
- Before doing this troubleshooting procedure, find out if the vehicle was in a collision. If so, verify that all the required components were replaced with new components of the correct part number, and that they were properly installed.
- Before doing this troubleshooting procedure, review SRS Precautions and Procedures and General Troubleshooting Information.
- Before replacing the SRS unit, check the SRS unit software version with the HDS. If the software version is not the latest, update the SRS unit software, and retest.
1. DTC check:
Check for DTCs with the HDS.
.png)
Are any SRS DTCs indicated?
YES
Go to SRS DTC troubleshooting.
NO
Go to step 2.
2. Body electrical system DTC check:
Check for body electrical DTCs with the HDS.
.png)
Is DTC U0151 indicated?
YES
Go to DTC U0151 troubleshooting.
NO
Go to step 3.
3. Gauge control module check:
Do the gauge control module self-diagnostic function.
Self diagnostic function
Does the front seat belt reminder indicator blink?
YES
Replace the SRS unit.
NO
Replace the gauge control module.
SRS SYMPTOM TROUBLESHOOTING - SRS INDICATOR DOES NOT COME ON
NOTE:
- Before doing this troubleshooting procedure, find out if the vehicle was in a collision. If so, verify that all the required components were replaced with new components of the correct part number, and that they were properly installed.
- Before doing this troubleshooting procedure, review SRS Precautions and Procedures and General Troubleshooting Information.
- SRS unit connector A (39P) type: Before replacing the SRS unit, check the SRS unit software version with the HDS. If the software version is not the latest, update the SRS unit software, and retest.
1. Problem verification:
- Turn the vehicle to the OFF (LOCK) mode, then wait for 10 seconds.
- Turn the vehicle to the ON mode, and check that the SRS indicator comes on for about 6 seconds and then go off.
Does the SRS indicator come on for about 6 seconds and then go off?
YES
Intermittent failure, the vehicle is OK at this time.
NO
The failure is duplicated. Go to step 2.
2. Gauge control module check:
- Turn the vehicle to the OFF (LOCK) mode.
- Connect the HDS to the data link connector (DLC).
- Turn the vehicle to the ON mode.
- Do the gauge control module self-diagnostic function.
Does the SRS indicator blink?
YES
Replace the SRS unit.
NO
Replace the gauge control module.
READ NEXT:
SRS Symptom Troubleshooting - SRS Indicator Stays ON, But No DTCS
Are Stored, Or Cannot Be Read
NOTE:
Before doing this troubleshooting procedure, find out if the vehicle was
in a collision. If so, verify that all the required components were replaced
with new components of the correct par
Disposal
AIRBAG AND TENSIONER DISPOSAL (KA/KC)
Special Tools Required
Deployment Tool 07AAZ-000A100
Inspection
NOTE:
Before scrapping any front airbags, side airbags, side curtain airbags,
driver's seat b
Component Replacement/Inspection After Deployment
SRS COMPONENT REPLACEMENT/INSPECTION AFTER DEPLOYMENT (KA/KC)
Inspection
1. Component Replacement/Inspection After Deployment - Inspect
NOTE:
Do not repair damaged SRS wiring. Replace the affected w
SEE MORE:
DTC Troubleshooting 68-11: Brake Pedal Position Switch Stuck OFF
NOTE:
Troubleshoot any PGM-FI DTCs first.
Before you troubleshoot, review the how to troubleshoot the VSA system.
1. VSA modulator-control unit performance check:
Start the engine.
Check the parameter(s) below with the HDS. Do not press the brake pedal.
Is there 10 MPa or less?
YES
Go to s
Functional Setup - Audio System Diagnostic Mode
Select the item you want to check.
Backup Data Clear
Save Users Memory
LaneWatch (With Lanewatch)
Phone Picture
Anti-Theft Skip
Other
Backup Data Clear
This screen initializes the back-up data in the audio unit.
All Clear
Cookie Clear (Not available in this model (grayed out) )
Cache Cl
