Honda HR-V Owners & Service Manuals

Honda HR-V: General Information

Honda HR-V (2015-2021) Service Manual / Brakes / VSA System - Testing & Troubleshooting / General Information

HOW TO ENTER VSA MAINTENANCE MODE

Procedure

1. Maintenance Mode - Enter

NOTE:

  • Entering condition of VSA Maintenance Mode - Refer to: VSA System Description - Hill Start Assist Control, or VSA System Description - System Diagram, or VSA System Description - Engine Drag Torque Control, or VSA System Description - Automatic Brake Hold, or VSA System Description - Brake Assist Control, or VSA System Description - VSA Control, or VSA System Description - TCS Control, or VSA System Description - ABS Control, or VSA System Description - Overview, or VSA System Description - VSA OFF MODE.
  • When the VSA Maintenance Mode is activated, the VSA and TCS functions are disabled.
  • During the Maintenance Mode, the VSA OFF indicator flashes and the VSA indicator is on.

    When the power is switched to OFF Mode or the VSA OFF switch is pressed again, the Maintenance Mode is cancelled and both indicators go off.

  • In cases where following events occur, turn the power switch off, wait 10 seconds or longer and retry the procedure.
    • The procedure required to enter VSA Maintenance Mode is not followed properly.
    • The procedure is not completed within 30 seconds.
  • To terminate the maintenance mode, do the either one of the following procedures.
    1. Turn the vehicle to the OFF (LOCK) mode.
    2. Press VSA OFF switch for 0.5 sec. (make sure VSA indicator and VSA OFF indicator go off)
  • When the VSA detects a malfunction, the Maintenance Mode is cancelled.
  1. Turn the vehicle to the ON mode and do the following procedure within 30 seconds
  2. Release the parking brake and hold down the brake pedal. While holding down the brake pedal, press the VSA OFF switch. If the VSA OFF indicator turns on, press the VSA OFF switch again to see if the VSA OFF indicator goes off
  3. Release the brake pedal and apply the parking brake. While the brake pedal is released, press the VSA OFF switch. If the VSA OFF indicator turns on, press the VSA OFF indicator again to see if the VSA OFF indicator goes off
  4. Hold down the brake pedal while apply the parking brake. Press the VSA OFF switch while both brakes are applied. If the VSA OFF indicator turns on, press the VSA OFF switch again to see if the VSA OFF indicator flashes and the VSA indicator turns on.

    READ NEXT:

     Symptom Troubleshooting

     ABS Indicator, Brake System Indicator (RED), VSA Indicator, And Brake System Indicator (Amber) Do Not Go OFF (VSA System)

    Diagnostic procedure 1. F-Can Circuit Troubleshooting 2. VSA System Symptom Troubleshooting - VSA cannot be turned OFF or VSA System Symptom Troubleshooting - ABS indicator, brake system indicator (r

     VSA System Symptom Troubleshooting - ABS Indicator, Brake System Indicator (Red), VSA Indicator, And Brake System Indicator (Amber) Do Not Go OFF

    1. DTC check: Turn the vehicle to the ON mode. Check for DTCs with the HDS. Are there DTCs indicated? YES Do the DTC troubleshooting. NO Go to step 2. 2. Gauge control module operation check. D

    SEE MORE:

     A/C Signal Circuit Troubleshooting

    1. A/C compressor clutch condition check. Start the engine, and let it idle. Turn the blower switch on. Turn the A/C switch on. Check the parameter(s) below with the HDS. Do the current condition(s) match the threshold? YES Go to step 2. NO Do the A/C system test. 2. A/C system check. Check

     Engine Does Not Start

    Checking the Engine If the engine does not start, check the starter. If you must start the vehicle immediately, use an assisting vehicle to jump start it. Models with smart entry system If the Smart Entry Remote Battery is Weak If the beeper sounds, the indicator on the ENGINE START/STOP button fla

    © 2019-2025 Copyright www.hohrv2.com