Honda HR-V Owners & Service Manuals

Honda HR-V: Testing

FRONT PASSENGER'S WEIGHT SENSOR UNIT INITIALIZATION

Procedure

NOTE:

  • The front passenger's weight sensor unit initialization initializes the front passenger's weight sensor.
  • When you replace the front passenger's weight sensor unit, initialize the front passenger's weight sensor with the HDS.
  • When you replace or remove the front passenger's weight sensor, the front passenger's seat frame, or the front passenger's seat rail, initialize the front passenger's weight sensor with the HDS.

1. HDS - Connect

2. Front Passenger's Weight Sensor - Initialize

NOTE:

  • Before initializing the front passenger's weight sensor, clear the DTCs.
  • Before initializing the front passenger's weight sensor, make sure the 12 volt battery is fully charged.
  • Make sure all components of the front passenger's seat are correctly installed.
  • Make sure nothing is on the front passenger's seat, including aftermarket seat covers or mats.
  • Make sure nothing is in the front passenger's seat-back pocket.
  • Keep the windows and the moonroof closed (if equipped).
  • Do all initialization procedures, except test-driving, in the service bay.
  • Make sure the vehicle is on level ground.
  • Dehumidify inside of the vehicle with A/C.
  • Do not touch the front passenger's seat during the initialization.
  • Do not expose the front passenger's seat to sudden temperature changes.

1. Position the front passenger's seat all the way rearward, and adjust the seat-back to the forward most position. Do not move the seat from this position until the initialization is completed

2. Drive the vehicle, and accelerate to 22 mph (36 km/h), then stop on level ground

3. From SRS in the HDS Main Menu, select SWS, then Adjustment. In the Adjustment Menu, select SWS Initialization. Follow the prompts until the front passenger's weight sensor initialization has been completed

4. Turn the vehicle to the OFF (LOCK) mode.

FRONT PASSENGER'S WEIGHT SENSOR UNIT UPDATE

Special Tools Required

MVCI unit with the latest control module (CM) update software installed

Supplemental Restraint System - Testing & Troubleshooting

Procedure

1. Front Passenger's Weight Sensor Unit - Update

NOTE: Check any official service website for more information about updating the MVCI and control units.

SRS UNIT UPDATE

Any one of the above updating tools can be used.

Special Tools Required

MVCI unit with the latest control module (CM) update software installed

Supplemental Restraint System - Testing & Troubleshooting

Any one of the above updating tools can be used.

Procedure

1. SRS Unit - Update

NOTE: Check any official service website for more information about updating the MVCI and control units.

    READ NEXT:

     Check

    DRIVER'S SEAT POSITION SENSOR OPERATION CHECK Procedure NOTE: Check the driver's seat position sensor operation after the driver's seat position sensor replacement. 1. HDS - Connect 2. Driver's Seat

     Symptom Troubleshooting

     SRS Symptom Troubleshooting - Front Passenger's Airbag ON Indicator Does Not Go OFF

    NOTE: Before doing this troubleshooting procedure, find out if the vehicle was in a collision. If so, verify that all the required components were replaced with new components of the correct par

    SEE MORE:

     Synchro Ring and Gear Inspection (M/T)

    Inspection 1. Synchro Ring and Gear - Inspect Inspect the synchro rings for scoring, cracks, and damage (A) Inspect the inside of each synchro ring (B) for wear. Inspect the teeth (C) on each synchro ring for wear (rounded off). Inspect the teeth (A) on each synchro sleeve and matching te

     Check

    DRIVER'S SEAT POSITION SENSOR OPERATION CHECK Procedure NOTE: Check the driver's seat position sensor operation after the driver's seat position sensor replacement. 1. HDS - Connect 2. Driver's Seat Position Sensor - Operation Check Make sure the driver's seat is in the full forward position Fr

    © 2019-2024 Copyright www.hohrv2.com